What does the code LF mean on a Whirlpool Cabrio washer

Whirlpool Washer LF Error is a water fill error, it stands for Long Fill. It means that the main control has not gotten a signal back from the water pressure sensor which means that water is not filling the tub or not filling the tub fast enough. The control will shut down the cycle and report the LF error.

How do you fix the LF code on a Whirlpool Cabrio washer?

LF in the display Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve. This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.

How do you fix Whirlpool Lo FL?

1. Make sure the water supply is turned on and you have proper water pressure being supplied to the machine.
2. Make sure the water supply hoses are not kinked or pinched and that screens in the supply line are clear of debris.

What does it mean when a washing machine says LF?

If F8 E1 or LF (too long to fill) appears in display, the washer is taking too long to fill. … Either the F8E1 or the LF error codes may indicate there is some problem with the water supply going to the washer. Please make sure both inlet hoses are connected and both hot and cold water supplies are turned on.

How do I clear the error code on my Whirlpool washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

Why won't my Cabrio washer fill with water?

Washing Machine Won’t Fill Because Water Inlet Valve Defective. Washing machines have a water inlet valve that allows both hot and cold water into the unit. … No continuity indicates an issue with the valve. When the water inlet valve is the cause for a Whirlpool Cabrio washer not filling with water, it must be replaced.

How do I reset my Whirlpool Cabrio washer?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.

Where is the inlet valve screen on a washing machine?

It is typically located right behind the washer. There may be two valves that supply hot and cold water to the washing machine inlets.

What does lf mean on Whirlpool dryer?

An LF (Lint Filter) Error Code indicates that the HybridCare™ filter has been removed. Place filter into dryer and make sure the handle is properly seated.

What does Fl mean on a washing machine?

If Samsung Washer FL Error Code appears on the display panel, it’s likely a door lock malfunction. It indicates the door lock cannot be locked after several attempts.

Article first time published on

Why does my Whirlpool washer says low detergent?

Detergent Level Low – This will light (yellow) if there is enough detergent in the Load & Go™ cartridge for only a few more cycles.

What are the codes for a Cabrio washer?

Fault CodeWasher ProblemuL (none)Unbalanced loadoL (F70)OverloadedSd (F71)Suds DetectionLid (F81)Open/Close Door Lid

What does FOD mean on Whirlpool washer?

Fod or F18 is displayed: Excessive foam formation, or suds, interrupted the program/cycle.

Does a Whirlpool washer have a reset button?

Method 1: Unplug it The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.

How do you run diagnostics on a Cabrio washer?

1. The washing machine should be in standby (off) mode.
2. Press and release the following buttons within 4 seconds. …
3. if successful “dt” should display on the washing machines indicator.
4. Within 5 seconds press “Start” all indicator lights should come on and 88 should be displayed.

How do I reset my Cabrio touch washer?

1. Press PAUSE/CANCEL twice to cancel the cycle. The washer will drain.
2. Press POWER.
3. Select the desired wash cycle.
4. Select the desired Modifiers and Options.
5. Press START.

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

What causes a washer to not fill up?

If your washer doesn’t fill with water, first check that the house water supply to the washer is on. If it is, and the washer won’t fill at all, the inlet valves might have failed. If the washer fills partially, the problem is likely with the temperature selector switch or water-level pressure switch.

What does lf mean?

LFDefinition:Looking forType:AbbreviationGuessability:3: GuessableTypical Users:Adults and Teenagers

How do I reset my Whirlpool front load washer?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

How do you unlock a Whirlpool washing machine?

Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.

How do you drain a Cabrio washing machine touch screen?

Find the “Pause/Cancel” button on the control panel. Press this button twice to drain the washer. Press the “Power” button and rotate the cycle selection knob to “Drain and Spin” to remove the remaining water from the load.

Why is my Whirlpool Cabrio washer not spinning?

The most common causes of a Whirlpool Cabrio not spinning are: Defective lid switch. Broken drive belt. Loose drive pulley nut.

How much does it cost to replace a washing machine water inlet valve?

Machine Inlet Valve Repair A washing machine inlet valve replacement costs $75 to $125.

What does LO FL mean on Whirlpool washer?

The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water. If the washer has an F8 E1 error or LO FL error, the door may be locked, and the control may be unresponsive.

What is FL error code?

It means that the contact disappears somewhere between the hatch lock and the control module path. You will have to remove the lock module. Then, using a multimeter, check the loop on contacts leading from the lock.

What is Lo in washing machine?

The washing machine error code LO indicates an issue with the washers door lock assembly. The door lock assembly has several different components inside that could cause it to fail.

What is 2X HE detergent?

The “2X” refers to the fact that the detergent is concentrated, which means it can clean more loads with less detergent (and it’s stored in a smaller, more compact bottle). It also includes a color-safe bleach alternative, so you don’t have to use separate bleach.

How long do Whirlpool Cabrio washers last?

Top loaders typically have a longer life than front load washing machines. This model should last about 14 years.

Why is my Whirlpool washer beeping?

Error “Beeps” are an audible signal that the machine makes to alert the user that something is not right. Typically this will happen if the washer door has not been opened and closed for at least 3 cycles. This code may appear when the washer is first turned on. Open and close the door to clear the display.