How do I reset my Hayward salt chlorinator

If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.

How do I reset my Hayward chlorinator?

To reset, move the switch to ‘Off’ and then back to ‘Auto’. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to ‘Super Chlorinate’ and back to ‘Auto’. It takes about 30 seconds for the unit to settle back on the default reading.

How do you reset inspect on Hayward?

If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.

How do you recalibrate Hayward salt chlorinator?

Turn Salt System Off and On With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”. You should hear a click within 10 or 15 seconds. When you do, press the diagnostic button five times in a row. The system will go through a recalibration process.

What should my Hayward chlorinator be set at?

How much salt does the system require? Salt Systems work best with approximately 3200 parts per million (ppm) of salt, which is roughly the equivalent to a teaspoon of salt per gallon. However, all Hayward Salt Systems are designed to operate with salt levels anywhere from 2700 ppm to 3400 ppm.

What happens if salt level is too high in pool?

Having too much salt in your pool water can result in unnecessarily increasing chemical expenses. But having too little salinity restricts the amount of chlorine being generated and can lead to algae and bacteria growth.

How do you test a Hayward salt Cell?

Turn off the power to the system and deactivate the pool pump before removing the Turbo Cell. Remove the Turbo Cell. Once removed, look through the cell and inspect for scale formation (light colored crusty or flaky deposits) on the plates and for debris that is caught on the plates.

What should my salt generator be set at?

We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.

Why is my salt cell light blinking?

If the “Inspect Cell” light flashes by itself it is an early indication that the salt generator needs a manual reset. Each cell is equipped with 500 operational hours and requires a manual reset once it expires. To reset the cell, hold down the “Diagnostic” button for 3-5 seconds.

What does inspect cell mean on salt water pool?

If both the “check salt” and the “inspect cell” lights stay on, it most likely means that no chlorine is being produced at this time and your salt level fell below 2300 ppm. Both lights will also stay on if the controller is set to the wrong turbo cell type, or if the cell is unplugged.

Article first time published on

Why is my salt water pool not generating chlorine?

Salinity. Chlorine generators need salt to produce chlorine and can’t do so if the amount of salt in the water is too low. The desired salinity level in a saltwater pool is between 2,500 and 3,500 ppm. … If your salinity is below 2,500 ppm, the generator will not be able to produce chlorine.

Why is my Hayward salt system not producing chlorine?

The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.

Is my salt chlorinator working?

The easiest way to ascertain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights. Ensure there is enough salt in the pool. … If there is no chlorine reading, the chlorinator will not be working. If you have been dosing with chlorine you won’t know.

What should my chlorinator read?

On a Hayward Salt Chlorinator, your salt reading should be between 2,700 – 3,400 PPM (parts per million) with the optimum level of 3,200 PPM.

What setting should my pool chlorinator be on?

Chlorine Feeders: For each 5000 gallons of pool water, add one 3″ chlorine tablet, more or less. Choose a mid-point setting on the 1-10 dial. The higher the setting, the greater the dissolution rate. A setting of 5 may be too high, and it depends on the number of tablets in the feeder.

What temperature does a Hayward salt Cell stop working?

In pool water temperatures that are 60 degrees or below, the salt generators simply shut down and by design do not allow the salt cell to ionize (breakdown) the salt and convert it to chlorine.

How do I reset my Hayward Aqua plus salt cell?

Turn the filter pump on. You must reset the system by entering the ‘Diagnostic Menu’ and then hitting the right arrow key once and then pushing the plus key once. This should reset the light and message.

How can I tell if my salt cell is bad?

1. The power center displays a Check Salt message. …
2. The Cell Warning light displays consistently, shutting off for only a short while after cleaning.
3. Voltage is higher than normal.
4. Amperage is irregular (it should normally be zero or just slightly above)

Can you use vinegar to clean a salt cell?

As a thumb rule, go for a mild solution with a perfect blend of water and vinegar. Soak the saltwater cell or hot tubs (as the case may be) in a container with vinegar solution for a night. The solution can remove all sorts of remaining debris within a fortnight.

How many bags of salt do I need to start my pool?

Setting Up a Salt Water Pool How much salt to add to the pool? To reach the initial salt level recommended by the salt system manufacturer (usually 2400-3200 ppm), you will need to add about 200 lbs of pure pool grade salt (NaCl), per 10,000 gallons of water.

How many bags of salt do I need for a 12000 gallon pool?

Current Salt LevelSalt Needed8,000 Gallon Pool12,000 Gallon Pool1,000147 lbs.220 lbs.2,00080 lbs.120 lbs.3,00013 lbs.20 lbs.

How long after adding salt to pool Can you swim?

It’s recommended to wait at least 20 minutes to swim after adding salt to your pool. If you’re adding calcium chloride to your pool water, it’s recommended to wait two to four hours before swimming again.

How do you reset Aqua Logic?

Press the ‘Menu’ until, ‘Default Menu’ appears on the display. This menu is where the ‘Inspect Cell’ message is stored. Press the (>) key, repeatedly, until ‘Inspect Cell, Hold + to reset‘ appears on the display.

Why does my chlorinator says no flow?

The most common reason for low or no flow is that the baskets are full of debris. … *Always turn the pump off before you remove the baskets, if your pool pump is below water level you will need to close the valves in front of the pump and set the multiport valve on the filter to ‘closed’.

What is the difference between Aqua Trol and Aqua Rite?

The AquaTrol has all the same functions and features of the Aqua Rite but with a lower chlorine output. The AquaTrol also has an integral time clock for control of the pool filtration pump. … The AquaTrol system typically installs in less than 30 minutes and is very easy to operate.

What does no flow mean on salt cell?

The “No Flow” light indicates that the flow switch is not detecting sufficient water passing through. Check the following: cleaning the cell or the filter (see how to backwash a DE Filter or Clean a Cartridge Filter). Replace the flow sensor.

How do I test my Pentair salt Cell?

Submerge the salt cell in a bucket of pool water, but do not get the wiring connections wet. Turn on the pump and activate the salt system. Put the output on the salt system at 100% for this test. Put the output back to the original setting when you are done.